You’ve had roots cleared out of a drain, or you suspect they’re back, and you’ve spotted root killer on the shelf at the hardware store. It’s a fair question whether a cheap product poured down the toilet could save you another plumber visit.

The honest answer is that root killers have a small, useful job, but it isn’t the job most people buy them for. They can slow roots down, but they can’t clear a blockage or fix the gap the roots came in through.

The short answer: tree root killers can slow regrowth in a drain that has already been cleared, but they can’t remove a root mass, clear a blocked drain, or seal the crack the roots got in through. For a lasting fix, roots are cut out and jetted, then the damaged joint is relined so they can’t get back in.

This guide explains how roots get into drains, what root killers are, what they can and can’t do, how to use them safely, and what lasts longer. If roots are blocking your drain now, our high-pressure jetting service cuts them out and flushes the line clean.

How Do Tree Roots Get Into Drains?

Roots find their way in through tiny gaps at joints and cracks, drawn by the moisture and nutrients inside the pipe. Once a fine root gets in, it grows into a thick mat that catches toilet paper and waste.

Older Adelaide sewers are especially prone. Many are made of clay or earthenware in short lengths, so there’s a joint every metre or so, and Adelaide’s reactive clay soils move enough over the years to open those joints up. Large trees in established suburbs do the rest.

If you’re not sure roots are the problem, our guide to tree roots in drains covers the warning signs and which trees cause the most trouble.

What Are Root Killers?

Root killers are herbicides made to kill or slow plant roots inside a pipe. They come in a few main types, and each works a little differently:

Type How it’s used How it works
Foaming root control products Mixed and poured or flushed into the drain, where they expand into a foam The foam fills the pipe and stays in contact with roots on the top and sides, not just the bottom
Crystals and granules (often copper sulphate) Poured or flushed down the toilet or into an inspection opening by a plumber Dissolve as water flows over them and damage the roots they touch
Professional root inhibitor treatments Applied by a plumber, usually after the drain has been cut and jetted Coats the pipe and remaining roots to slow regrowth for a period

Whichever type you look at, check that the product is registered for use in Australia and made for drains and sewers, and read the whole label before you buy it.

What Can a Root Killer Actually Do?

A root killer is a maintenance tool, not a fix. Used on a drain that’s already flowing, it can kill the fine roots that have started to grow back and slow down how quickly a new mat forms.

That makes it useful in a few situations. If a line has just been cut and jetted, a product used as directed can lengthen the time before roots build up again. It can also help on a known problem line while you plan a longer-term repair.

Research on sewer root control shows the effect does wear off. Roots usually start growing back within a couple of years, so treatment has to be repeated.

What Can’t a Root Killer Do?

A root killer can’t clear a blocked drain. If water is backing up, the product can’t reach the roots, and even if it does, dead roots still sit in the pipe and block it.

  • It won’t remove a root mass. Dead roots break down slowly, sometimes over many months, and can keep catching waste in the meantime.
  • It won’t fix the crack or open joint. The gap that let the roots in is still there, so new roots will find it again.
  • It won’t clear other blockages. Wipes, fat, or a collapsed section of pipe won’t be touched by a root product.
  • It won’t stop roots coming back for good. Every treatment is temporary.

That’s why roots so often return after a drain is cleared. Our guide on why roots come back after hydro jetting explains this in more detail.

Are Root Killers Safe to Use?

They can be, if you follow the label exactly. These are strong chemicals designed to kill plant tissue, so they need care.

Using a root killer safely

  • Read and follow the label exactly, including the amount, how to apply it, and how often.
  • Wear the protection the label asks for, usually gloves and eye protection, and avoid breathing in fumes or dust.
  • Never mix a root killer with bleach, drain cleaners, or any other chemical. Some combinations can react and release dangerous gas.
  • Don’t use it in a fully blocked drain. It can sit in the pipe or splash back up, and it makes the drain more dangerous for whoever clears it.
  • Store it locked away from children and pets, in its original container.
  • Never open an inspection opening (a screw cap on the sewer pipe) to pour a product in. That’s a job for a licensed plumber.

Back view of a Will’s Plumbing Adelaide technician carrying a large pipe during a relining project.

Some products can also harm nearby plants if they’re overused or spill onto the garden. Copper is a heavy metal that isn’t fully removed by sewage treatment, which is another reason not to use more than the label says.

What Lasts Longer Than a Root Killer?

The fix that lasts is to remove the roots and then close the gap they came in through. That’s usually a two-step job.

Step 1: Cut and Jet the Roots

A plumber cuts through the root mass with an electric eel or a root-cutting head, then uses high-pressure jetting to scour the pipe walls and flush the debris out. This restores full flow straight away.

Step 2: Seal the Entry Point

Once the line is clear, a camera shows exactly where the roots got in. If it’s one or two joints, a patch reline can seal just those spots from inside. If roots are getting in all along the pipe, a full liner seals every joint at once.

Pipe relining creates a smooth pipe with no joints for roots to get into. For many homes, that ends the cycle of blockages for good.

If You Can’t Repair Yet

If a repair isn’t possible right now, regular maintenance keeps roots under control. Having the drain cleared and jetted every 12 to 18 months stops roots from building up into a full blockage, and a root killer used as directed in between can help slow them down.

What Can I Check Safely?

Before you buy anything, a few simple checks tell you whether a root product is worth trying or whether you need a plumber first.

  1. Is the drain flowing? Run a tap or flush the toilet and watch. If water drains normally, a root product may be an option. If it’s slow or backing up, call a plumber first.
  2. Is the gully outside overflowing? If the grated drain outside the laundry or bathroom has water or toilet paper coming out, the line is blocked, and a root killer won’t help.
  3. When was it last cleared? If roots were cut out recently and the drain is fine, it’s a good time to think about prevention.
  4. How quickly did the roots come back? If the drain blocked again within months of being cleared, the pipe is probably damaged and needs a camera check.
  5. Where are the trees? Note any large trees or shrubs near the line of the sewer between the house and the street.

Don’t open any inspection opening, and don’t pour root killer into a drain that is slow or blocked.

Roots back in your drain?

Call 0484 600 095. We’ll cut out the roots, jet the line clean, and show you on camera where they’re getting in.

Upfront pricing before we start · Licensed and insured · All Adelaide metro suburbs

When Should I Call a Plumber?

Call a plumber whenever a drain is blocked or keeps blocking. A root killer is only for drains that are already flowing. Book a plumber if:

  • a drain keeps blocking, or blocks again within months of being cleared
  • sewage or toilet paper is coming out of the gully outside
  • water is backing up into the shower, bath or floor waste
  • Roots are found again soon after the drain was cut and jetted
  • You’ve used a root killer and the drain is still slow

How Do We Fix Root-Blocked Drains?

We clear the roots, check the pipe, and fix the entry point, so you’re not paying to clear the same drain every year.

  1. Clear the blockage. We cut through the roots and jet the line until it flows freely.
  2. Run a camera. A camera inspection shows how many joints are affected, whether the pipe is cracked, and where the roots are getting in.
  3. Talk you through the options. That might be a patch reline over one joint, a full liner, replacing a damaged section, or regular maintenance if a repair can wait.
  4. Fix it. Once you’ve chosen, we carry out the work and run the camera again so you can see the result.

Every job is quoted upfront before we start, and we’ll tell you honestly if regular maintenance is the better option for your home right now.

Stop paying to clear the same roots every year.

Wills Plumbing clears root-blocked drains across Adelaide and seals the entry points with relining, so roots can’t get back in.

Same-day service available · Upfront pricing before we start · Licensed and insured

Call 0484 600 095 or book high-pressure jetting.

Frequently Asked Questions

Will a root killer kill my tree?

Root killers for drains are made to act on the roots inside the pipe, not the whole tree, and used as the label directs, they’re not meant to harm it. Overusing a product, or spilling it onto the garden, can damage nearby plants. If you’re worried about a valued tree, talk to a plumber about cutting and relining instead, which removes the roots in the pipe without any chemicals.

Is copper sulphate safe to use in clay sewer pipes?

Copper sulphate is sold for root control in drains, but it only slows roots rather than removing them, and it can harm plants if overused. Copper is also a heavy metal that sewage treatment doesn’t fully remove. If you use it, follow the label exactly and never use it in a blocked drain. For an older clay sewer with roots, cutting, jetting, and relining last far longer.

How often should I use a root killer?

Only as often as the product label says. Using more, or more often, won’t make it work better and can harm nearby plants. Even used correctly, the effect wears off, and roots usually start growing back within a couple of years. If you find yourself treating the same drain again and again, the pipe probably needs a repair.

Can I pour root killer into a fully blocked drain?

No. If the drain is blocked, the product can’t reach the roots, and it can sit in the pipe or splash back up when the drain is cleared. That makes the job more dangerous for you and the plumber. Have the blockage cleared first, then decide whether a root product or a repair is the right next step.

Does hydro jetting remove tree roots?

Yes. High-pressure jetting, usually after the roots are cut with an electric eel or a cutting head, removes the root mass and scours the pipe walls clean. It restores full flow straight away. Jetting doesn’t seal the gaps the roots came through, though, so roots can grow back unless the damaged joints are relined or repaired.

How do I stop tree roots coming back for good?

Seal the gaps they get in through. Once the roots are cleared, a camera shows the damaged joints or cracks, and relining puts a smooth, joint-free pipe inside the old one so roots have no way in. A patch reline can fix one or two joints, while a full liner suits a pipe with roots all along it.

Fix the Gap, Not Just the Roots

Root killers can help slow roots in a drain that’s already flowing, but they won’t clear a blockage or stop roots for good. The lasting fix is to cut the roots out and seal the joint they came through. If roots keep blocking your drain, call Wills Plumbing on 0484 600 095.